Install a Vending Credit Card Reader in 5 Minutes - YouTube

My name is Samuel I am a customer success manager over here at parlevel

systems today we're going to be covering the installation of our parlevel pay

credit card bezels. The tools needed to install the parlevel

pay credit card reader will be the parlevel pay bezel, the parlevel telemeter

a drill guide, a drill bit, a step bit, the Dex cable, the MDB cable

the bezel cable, the included screws, a drill, a Phillips head screwdriver and lastly a

quarter inch socket set with deep sockets in place of the sockets a 7/32

and 1/4 inch nut driver can be used. The first step in this is going to be

removing the bill validator we're gonna be drilling holes into the machine so we

want to verify that we do not damage the validator in the process. You can

accomplish this by using a quarter inch or 7/32 socket to remove the four nuts

that are holding the validator in place. You're wanting to place the drill

pattern right above your bill validator and I recommend using a piece of tape to

hold the template in place. Make sure you get it fairly even on there

and using that we will then begin to drill the holes to mount this credit

card reader because I'm going to be using a smaller drill bit just to make

my holes. After drilling your pilot holes you can then remove the template and

you're wanting to step up the hole size accordingly. We're gonna step up the

smaller screw holes just a bit. Prior to installing the credit card bezel onto

the machine you're gonna want to plug in the credit card cable into the back of

the bezel, like so and then you're going to want to route the rest of the cable

through the large hole that you drilled out. Once you have started your screws

onto the back of the credit card bezel you'll then go with a Philips head

screwdriver to tighten up the screws.

After securing your credit card bezel to the machine you can then go ahead and

reinstall your bill validator back into the machine as well. Once you have

secured your bill validator you can then begin installing your parlevel box

telemeter. The recommended first step would be to connect all cabling prior to

mounting the actual parlevel box to the vending machine using the velcro

provided so I'm going to begin connecting the cables now. You have this

black connector coming off with a credit card bezel that's going to go into the

credit card reader slot of the credit card slot here. Then we have the Dex

cable that we will be plugging in to the back of the parlevel box which will go

in the Dex plug.

Lastly we can connect our MDB and then we also need to get an antenna here your

Parlevel telemeter should look just like, this you have an antenna cable, your

credit card reader, a Dex cable and an MDB cable connected to it as well.

All right you can then mount the parlevel telemeter inside the machine

that is most accessible to you. I am going to place it on this side of

the machine right here. Hold it for a few seconds so that it sticks in place.

Once it is mounted and you can then go in and connect the wires into the

vending machine. The first cable that I'm wanting to connect is going to be the

Dex cable. You will then find your Dex plug on the vending machine ours is

right here some of them are going to be on the actual board itself so have my

deck stable plugged in now I'm going to plug in my M DB line as you can see it

has a splitter on it we're going to separate at the bill validator and coin

mech going to the board. So I'm going to separate it here, plug in the machine.

Perfect everything is all connected now for you.

Lastly, we'll have the antenna that we have connected to the parlevel telemeter

That can be mounted anywhere inside or on the outside of the vending

machine. Once you have your green light and your welcome on your credit card

reader you're good to go. Your parlevel credit card reader is now up and running

and ready to boost your machine sales. Along with that you can go into our

Palevel VMS and view cashless reports, machine alerts and much much more.

If you have any questions please feel free to reach out to our support team

through email phone or our instant messenger slack and we will definitely

take care of you.