🔍
How to Install Gear In Normal Cycle | Install Gears In Any Cycle | 7 Speed Gear Installation - YouTube
Channel: unknown
[12]
Guys welcome to my channel friends if you
have normal cycle or single speed cycle and
[19]
you want to install gears the this video is
going to be very useful for you, in this video
[25]
i will tell you how to do it at home in simple
step. This whole installation process I have covered
[29]
step by step in this video and you can convert your single speed cycle to gear cycle
[33]
By following all these steps you can covert your single speed cycle to gear cycle
[37]
So friends start our video and convert our single speed cycle in gear cycle
[44]
In the first step, we remove rear tyres,
[51]
to remove these wheels, you will need a 15
size spanner, we loose it, there is no need
[59]
to open it completely, after which easily
loosen the nut on the other side. Let us now
[66]
push it slowly a little bit and your wheels
will come out, friends, our tire is out
[77]
After removing the tire, we will cold expansion this frame.
[82]
The frame designed for normal single
[85]
speed bicycle is a 7" axle, you'll need a
7.5-inch axle to install the 7 speed gear,
[90]
and you'll need to tweak your frame a bit
to fit this axle into your frame. You will
[95]
have to expand a bit, for this you have to
fit it in the 7.5 inch axle into the frame, then tighten
[107]
it slowly from inside, after tightening it
completely, your frame has been expanded,
[115]
now you can do it for 24 hours. So that your
frames will expand properly.
[124]
Friends, in this step we will remove single
speed free wheel.
[129]
freewheel is a little tricky process, normally
there is a special tool for freewheel remove
[135]
all but you can remove it without this tool
also. For this, you have to take the help
[140]
of a pointed object and hammer, you have to
place this pointed object on the holes of
[147]
the freewheel and then push it in the same
direction in which the freewheel is moving.
[151]
Friends, if you have been using your cycle
for a long time, then these freewheels can
[155]
become jammed and for this you will have to
put a little extra effort.
[171]
Our Single Speed Freewheels Are Removed
[182]
In this step we will install the 7.5 inch axle.
[186]
For this, first you have to read the old axle removal,
[190]
we have to open these attached nuts slowly, after that your axle will be easily removed.
[197]
axle is removed, you have to take care of one thing that no ball gets removed from it if any balls
[202]
come out from it during process then you have to re-position these balls and fit the axle back.
[210]
We take out the axle from the frame that was cold expanded,
[214]
this axle half an inch long from the single speed axle.
[218]
Now we insert this 7.5 inch axle into it and tighten these nuts slowly this is our 7.5 inch axle installed.
[233]
In this step we will talk about how to install
7 Speed Free wheel .
[238]
This is our 7 Speed Freewheel, 6 Speed Freewheel also have to use the same process.
[249]
It is fitted with the first hand, after fitting it slowly tightens clockwise, it does not need to be
[254]
tightened completely, it will automatically
get tight during paddling.
[259]
We need to install these additional nuts so that the gap remains in the freewheel end frame and
[267]
your freewheel does not collide with your
frame.
[271]
The installation of our 7 Speed Freewheel is complete.
[275]
Guys let's start the installation of our derailleur
[280]
Friends in this step we have to fit our derailleur in the frame
[287]
for that first you have to open the lock nut of the derailleur,
[292]
after opening the lock nut fit it in the groove of the frame
[300]
Tighten the derailleur well with the help of a screw driver.
[313]
Friends, with this the installation of our derailleur has also been completed.
[321]
Now lets install the rear wheel.
[326]
We have set the long axle now let's adjust it in the frame with these long axle.
[334]
Friends, we did the cold expansion of the frame in the first step,
[337]
that's why it is very easy to see that
your tires fit in the frame here.
[346]
If you have difficulty fitting then you can expand the frame a bit so that it will install well your tire
[352]
Let us set the wheels well, set the tyres in the center of the frame that
[361]
after that gradually tighten the nuts from
both the sides,
[366]
now with this our rear wheel installation is also completed.
[372]
Friends move
towards our chain installation.
[377]
To break the chain, normally you need a chain breaker tool,
[380]
but even if you do not have this tool, there is no problem
[385]
you can break it with the help
of simple nail, screw driver and hammer.
[392]
To convert a single speed chain to a seven
speed chain, you will need to add seven links
[398]
By adding a small link, your chain
will become seven speed compatible and you
[402]
will not need to get a new chain. I am using
new chain here.
[458]
Our chain installation process is complete.
[467]
Friends, now let's install the shifters
[471]
To install the shifters, first you have to take out the
grips.
[481]
I have seven speed shifters
[483]
Remove the brake levers to install
them. But if you are using grip shifters then
[492]
you do not need to remove brake lovers for
that. The handlebars insert the shifters,
[499]
after that the brake levers are also set, now
its handle grip is put back in it.
[509]
Tight these barke levers well with the help
of allen key,
[513]
After that also tighten the shifter.
[517]
Friends fit the wire with frame,
for that you have to insert it
[522]
in the wire cover and fit it according to
the frame,
[527]
if you have given hooks to fit if in your frame then you can fit it in this way
[533]
but In case of not having these hooks,
[537]
then you can directly fit it in the frame with the help of wire tye
[541]
by putting it in the wire cover.
[543]
Moving on to the most important step, gear tuning,
[548]
Keeping the chain on the freewheel in the same position as the gears on the shifter.
[554]
Here they keep the chain in the 7th gear and also keep the shifters in the position of the 7th gear.
[562]
Pull the wire tight only and with the help
of these knots make it tight.
[572]
Properly bend the additional wire.
[582]
Now you have to see that the position of your derailleur jockey wheel
[586]
and your gear is in straight line. If it is not in straight light then your chain will derail.
[595]
you can use the limit screw to adjust the jockey wheel
[598]
The position of the jockey wheel can be set to the left or right.
[602]
For this, I will make a detailed video in which I will tell you the tuning
[606]
after setting the position of our
jockey wheel and gear, now we check whether
[613]
the shifting of our gears is getting proper
or not.
[618]
Guys see our gears are changing well
[631]
and shifters and gears are working properly
with this our installation process is completed
[662]
If you liked this video please subscribe my
channel for such latest videos.
[668]
Don't forget to like share and comment this video.
[671]
So Guys Keep Paddling thanks for watching this Video Thank you
Most Recent Videos:
You can go back to the homepage right here: Homepage